静置/好氧/缺氧序批式反应器（SBR）脱氮除磷效果研究

以静置段代替传统厌氧段,采用后置缺氧方式,考察了静置/好氧/缺氧序批式反应器(SBR)(R1)的生物脱氮除磷(BNR)性能,并与传统厌氧/好氧/缺氧序批式反应器(SBR)(R2)进行对比.两反应器进水乙酸钠、氨氮(NH+4-N)及磷酸盐(PO3-4-P)浓度均分别为350 mg·L-1(以COD计)、40 mg·L-1及12 mg·L-1,水力停留时间(HRT)为12 h.研究结果表明,R1长期运行中磷的去除率与R2相当,分别为92.4%和92.1%,而总氮(TN)去除率则较R2高,分别为83.5%和77.0%.R1静置段省去搅拌但仍能起到厌氧段的作用,为好氧快速摄磷奠定了基础,同时R1缺氧段发生反硝化摄磷,使出水磷降至0.91 mg·L-1.好氧段内R1发生了同步硝化-反硝化(SND),贡献了18.0%的TN去除量,R2也存在SND,但脱氮贡献率较少,仅为9.8%.R1和R2后置缺氧反硝化均以糖原驱动,反硝化速率分别为0.98、0.84 mg·g-1·h-1(以每g VSS产生的N(mg)计),出水TN分别为6.62、9.21 mg·L-1.研究表明,静置段代替传统厌氧段后,可获得更好的脱氮效果,且工艺更为简化.     

HNO_3在气相及SiO_2表面的紫外光解反应

利用紫外及红外吸收光谱等分析手段对365 nm光照下HNO3在气相与SiO2表面的光解反应进行了研究.考察了HNO3浓度、光照时间、相对湿度等条件对反应的影响.结果表明:随着HNO3浓度及光照时间的增加,光解产生的NO2和NO浓度均呈指数增加;无水汽情况下,400 Pa的HNO3光解45 min后,产生NO2及NO浓度比气相光解产生的分别高约3及1.7倍.HNO3光解产生的HONO的浓度随相对湿度的增加而呈线性增加,在SiO2颗粒物表面光解产生的NO2浓度随着相对湿度的增加而减少,而NO浓度则随之增大.400 Pa的HNO3光照45 min后,SiO2表面光解产生的HONO浓度是气相光解的3倍、SiO2表面暗反应的约30倍.     

Blast wave clearing behavior for positive and negative phases

The purpose of the research was to improve prediction of response of buildings to blast waves by including the negative phase and considering clearing of both positive and negative phases. Commonly used structural design practices, which trace their origins to military design manuals, often ignore the negative phase as well as positive phase clearing. For high explosive threats, this approach is conservative in most circumstances. However, negative phase clearing had not previously been studied for blast waves, and the implications for structural response had not been evaluated. This paper presents results of modeling negative phase blast clearing behavior for a typical blast wave and discusses the differences from positive phase clearing. The implications of including positive and negative phase clearing in building blast damage analysis are also investigated through single-degree-of-freedom (SDOF) analyses.Blast waves from explosion sources like a vapor cloud explosion (VCE), pressure vessel burst or high explosive exhibit both positive and negative phases, and the relative magnitude of the positive and negative phases varies among explosion sources and the specific circumstances of each source. A fully reflected blast wave is produced if an incident blast wave were to strike an infinitely tall and wide wall in a normal orientation. Both the positive and negative phases of the blast wave are enhanced by the reflection process. However, when an incident blast wave strikes a wall of finite size in a normal orientation, rarefaction waves are created at the edges of the wall, and the rarefactions sweep down from the roof and inward from sides. The rarefaction waves result in a clearing effect for both the positive and negative phases.Clearing relieves some of the applied blast load on the reflected wall for the positive phase. However, this is not always the case for the negative phase. As shown by the results presented in this paper, clearing may either relieve or enhance the applied negative phase blast load, depending on the duration of the blast wave and the wall dimensions.The impact of negative phase clearing on structural response for generic building components was also investigated. Nonlinear SDOF methods were used to characterize response in terms of peak positive and negative displacements. It was found that the influence of the negative phase is significant and the peak structural response can occur during negative (outward) displacement.     

卷烟膨胀烟丝生产线冷端CO_2泵装置的优化改进

为解决干冰膨胀烟丝生产线冷端液体工艺泵因机械密封长期超压和气缚现象造成损坏发生CO2泄漏而导致紧急停机抢修的问题,对干冰膨胀线冷端工艺罐系统进行了优化改进。在工艺泵吸口前管路引一根气相平衡管至工艺罐顶部,当泵吸口前管路有CO2液体时,输送管路内气化的CO2气体通过气相平衡管线释放回工艺罐内,不会进入工艺泵体内。应用结果表明,工艺泵内的憋压和气缚现象消失了,机械密封受到保护。改造前机械密封平均一个季度更换一次,改造后机械密封使用5年未损毁,达到保护干冰膨胀线冷端工艺泵机械密封的目的。     

典型可燃物燃烧烟尘物化特性差异性研究

开展对典型可燃物燃烧烟尘的物化特性差异性研究,是全面了解烟尘信息的基础.基于可控条件下的燃烧试验,对典型可燃物燃烧烟尘物理特性和化学组分进行了分析.通过对比分析汽油燃烧烟尘、聚苯乙烯燃烧烟尘、ABS燃烧烟尘及柴油烟尘和正庚烷烟尘的透射电镜图片,对透射电镜图的紧凑性、复杂性及灰度值进行了深入分析,探讨了燃烧烟尘的物理差异性.利用固相微萃取-气质联用技术(SPME-GC-MS),对汽油燃烧烟尘、聚苯乙烯燃烧烟尘、ABS燃烧烟尘化学组分进行了分析和对比.通过燃烧烟尘的特征物质组分的分析,得到3种燃烧烟尘在特征物质的分布和出峰时间等方面的差异性.这些差异性可作为对烟尘来源及燃烧条件等因素判别的依据.     

Analysis of trace dicyandiamide in stream water using solid phase extraction and liquid chromatography UV spectrometry

An improved method for trace level quantification of dicyandiamide in stream water has been developed. This method includes sample pretreatment using solid phase extraction. The extraction procedure (including loading, washing, and eluting) used a flow rate of 1.0 mL/min, and dicyandiamide was eluted with 20 mL of a methanol/acetonitrile mixture (V/V = 2:3), followed by pre-concentration using nitrogen evaporation and analysis with high performance liquid chromatography–ultraviolet spectroscopy (HPLC–UV). Sample extraction was carried out using a Waters Sep-Pak AC-2 Cartridge (with activated carbon). Separation was achieved on a ZIC^®-Hydrophilic Interaction Liquid Chromatography (ZIC-HILIC) (50 mm × 2.1 mm, 3.5 μm) chromatography column and quantification was accomplished based on UV absorbance. A reliable linear relationship was obtained for the calibration curve using standard solutions (R² > 0.999). Recoveries for dicyandiamide ranged from 84.6% to 96.8%, and the relative standard deviations (RSDs, n = 3) were below 6.1% with a detection limit of 5.0 ng/mL for stream water samples.     

金属粉尘湿法处理系统的设计和除尘效果分析

为改善金属抛光操作人员的工作环境、降低抛光金属粉尘的爆炸风险，设计一种金属粉尘湿法处理系统，并通过建立多相流动数值模型，探究其内部流场特征与金属粉尘运动规律，分析金属粉尘湿法处理系统的除尘效率。研究结果表明:大粒径的金属粉尘直接重力沉降至水槽中；小粒径(PM10)的金属粉尘易随气流进入风道，进而通过水雾脱除；采用洁净进气源，可以有效降低工人操作环境的粉尘浓度；增加细水雾，可以有效提高金属粉尘湿法处理系统的除尘效率，对PM10的除尘效率从30%提升至82%。     

屏蔽服冷却系统对人体表面温度影响的研究*

为科学有效地论证多种方式组合的冷却屏蔽服在不同环境条件下对人体表面温度控制的效果，需要对冷却系统及人体敏感部位发热量进行客观评估。通过对5名健康男性的高温测试，探究人体在不同环境温度下体表温度的变化，得出胸部、背部及额头为热量最高部位，并构建以“人体-降温屏蔽服-外界环境”为主体的冷却系统数值模型，对不同环境中的屏蔽服冷却效果展开研究，分析穿戴冷却屏蔽服时人体躯干部分的温度分布及影响。结果表明:在屏蔽服中靠近胸部、背部部位引入相变材料和风扇，均可帮助人体降低体温，提高舒适度。     

液氮泡沫发生器内流动特性研究

低温液氮与泡沫混合液直接接触产生氮气泡沫是一种新型的掺混形式,利用液氮高汽化比的特点,搭建液氮泡沫可视化实验装置,进行氮气-水两相流及液氮泡沫流动特性的研究。结果表明,液氮相变产生大量氮气,其与泡沫液混合产生泡沫,温度有所回升,最终趋于泡沫混合液温度;管路沿程压降较小;液氮射流破碎及流动过程可分为6个区域:低温液氮区、向上循环翻滚区、滞留区、泡沫与泡沫混合液混合区、致密泡沫区、泡沫混合液区。流体向下游流动过程中持续发泡;为防止管路结冰,需合理控制泡沫混合液与液氮流量。     

基于ZIF-L的微固相萃取技术测定地表水中痕量典型多环芳烃

制备类沸石咪唑酯骨架ZIF-L材料,将其用作微固相萃取吸附剂,处理水中萘、苊、苊烯、芴、菲、蒽、荧蒽、芘等8种痕量典型多环芳烃,再用HPLC测定。试验表明,ZIF-L对上述多环芳烃的萃取效率明显高于商品化萃取材料C 18和多壁碳纳米管。方法在0.100μg/L^200μg/L范围内线性良好,方法检出限为0.02μg/L^0.03μg/L,标准溶液5次测定结果的RSD为4.7%~9.5%,实际水样加标回收率为84.5%~115%。将该方法用于北太湖5个点位水样的测定,测定值为未检出~3.40μg/L。